Premium Stock

Jurassic Park 25th Anniversary 3D Figurine in Diorama | Assembly

(57)
cm: 44.3 w x 32.8 d x 25.2 h
in: 17.441 w x 12.913 d x 9.921 h

Source Files

|

Description

|

Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Jurassic Park 25th Anniversary 3D Figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS). Files for each version are available for download after the purchase.

Detailed information about this model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
4_Ge_lock_10H_(x21)_FDM ( repaired).stl
0.03 MiB 4 min <1 m 18 x 10 x 2 Download
5_Body_FDM (repaired).stl
24.55 MiB 53 h 39 min 36 m 93 x 101 x 174 Download
6_Hand_R_FDM (repaired).s tl
1.56 MiB 1 h 57 min 1 m 58 x 28 x 34 Download
7_Hand_L_FDM (repaired).s tl
1.51 MiB 1 h 37 min 1 m 52 x 34 x 36 Download
8_Leg__R_FDM (repaired).s tl
14.64 MiB 28 h 49 min 22 m 57 x 123 x 187 Download
10_Tail_1_FDM (repaired). stl
8.04 MiB 10 h 17 min 6 m 52 x 68 x 86 Download
11_Tail_2_FDM (repaired). stl
6.52 MiB 8 h 52 min 6 m 78 x 52 x 128 Download
12_Platform_1_FDM (repair ed).stl
9.37 MiB 33 h 11 min 19 m 170 x 177 x 40 Download
13_Platform_2_FDM (repair ed).stl
13.45 MiB 40 h 23 m 172 x 165 x 42 Download
14_Platform_3_FDM (repair ed).stl
11.40 MiB 30 h 36 min 17 m 169 x 154 x 36 Download
16_Fence_1_FDM (repaired) .stl
6.14 MiB 6 h 5 min 4 m 172 x 149 x 33 Download
17_Fence_2_FDM (repaired) .stl
4.98 MiB 10 h 30 min 7 m 190 x 193 x 34 Download
19_Wheel_1_FDM (repaired) .stl
1.91 MiB 1 h 25 min 1 m 34 x 35 x 13 Download
20_Wheel_2_FDM (repaired) .stl
1.93 MiB 1 h 25 min 1 m 34 x 35 x 14 Download
21_Wheel_3_FDM (repaired) .stl
1.91 MiB 1 h 25 min 1 m 34 x 35 x 14 Download
22_Wheel_4_FDM (repaired) .stl
1.93 MiB 1 h 25 min 1 m 34 x 35 x 13 Download
23_GE_Connector_B_C_(x4)_ FDM (repaired).stl
0.08 MiB 9 min <1 m 25 x 6 x 6 Download
1_Lower_jaw_V2_FDM (repai red).stl
17.10 MiB 3 h 29 min 2 m 53 x 66 x 41 Download
2_Head_V2_FDM (repaired). stl
20.81 MiB 23 h 45 min 15 m 56 x 92 x 132 Download
3_Upper_jaw_V2_FDM (repai red).stl
17.93 MiB 1 h 13 min 1 m 38 x 43 x 24 Download
18_Car_dirty_FDM (repaire d).stl
18.99 MiB 46 h 40 min 32 m 196 x 186 x 72 Download
24_Car_Dirty_front_FDM (r epaired).stl
20.89 MiB 14 h 16 min 8 m 86 x 66 x 64 Download
25_Car_Dirty_back_FDM (re paired).stl
26.70 MiB 30 h 12 min 19 m 124 x 159 x 56 Download
26_Car_Clean_FDM (repaire d).stl
29.68 MiB 46 h 26 min 31 m 132 x 212 x 72 Download
27_Car_clean_front_FDM (r epaired).stl
26.63 MiB 14 h 3 min 9 m 86 x 68 x 64 Download
28_Car_clean_back_FDM (re paired).stl
34.08 MiB 30 h 16 min 19 m 124 x 159 x 56 Download
9_Leg_L_FDM (repaired).st l
17.49 MiB 18 h 1 min 12 m 43 x 152 x 119 Download
28_v2_logoless_Car_clean_ back_FDM (repaired).stl
39.61 MiB 29 h 34 min 19 m 124 x 159 x 56 Download
17_1_Fence_2_FDM(repaired ).stl
15.00 MiB 6 h 26 min 4 m 125 x 69 x 31 Download
17_2_Fence_2_FDM(repaired ).stl
15.73 MiB 6 h 46 min 4 m 109 x 82 x 29 Download
15_Platform_4_FDM (repair ed).stl
18.89 MiB 40 h 5 min 21 m 171 x 176 x 44 Download
...

HISTORY OF THIS 25TH ANNIVERSARY DIORAMA

The head of "InGen" Professor John Hammond finds a way to recreate dinosaurs through genetic engineering. The genetic material he finds in mosquitoes which millions of years ago drank the blood of dinosaurs and then sitting on a tree bogged down in wood tar forming inclusions. The missing fragments of code in DNA are supplemented with fragments of the code of modern amphibians - frogs. Hammond creates a huge park the inhabitants of which are dinosaurs. But everything went not according to plan. The programmer who was hired by the competitors turned off the security to steal DNA samples. Due to disabling the protection of dinosaurs were able to go beyond the enclosures. The car with Hammond's grandchildren stopped right next to the Tyrannosaur cage and this diorama captured that famous moment from this film.

ABOUT THIS 3D MODEL

The model is saved in STL files, a format supported by most 3D printers

FDM version features:
- Contains 25 parts;
- Made with removable teeth in order to print them with the best quality;
- Made with a divided platform for any buildplate sizes;
- Comes with two variants of the flipped car for you to choose from - a clean variant, and one covered in dirt;
- Made with s lock (4_Ge_lock_10H_(x17) that you need to print 17 times;
- All parts are divided in such way that you will print them with the smallest amount of supports.

DLP/SLA version features:
- Same as FDM but smaller, also made as 13 parts;

DLP/SLA Eco version features:
- Same as the DLP/SLA version, but contains parts hollowed out to save resin;

SLS version features:
- Same as SLA but made as 2 parts for economy your material;

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.3.1. or Simplify3D softwares.

There are 25 parts for FFF/FDM version, 13 parts for DLP/SLA and for DLP/SLA Eco versions, and 2 part for SLS.

Scale: Height of T-Rex is 4000 mm. The scale of this Diorama was made in proportion to him. 1/20 for FFF/FDM version and 1/40 for DLP/SLA/SLS version.

FFF/FDM version dimensions:
After being printed will stand -  252 mm tall, 443 mm wide, 328 mm deep;

DLP/​SLA/SLS version dimensions:
After being printed will stand - 126 mm tall, 222 mm wide, 164 mm deep;
- Has a few details, to keep printing costs down.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Jurassic Park 25th Anniversary​ 3D Figurine of Diorama for 3D printing which consist of 53 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of the Jurassic Park 25th Anniversary;
- Detailed settings that we provide for Cura 3.3.1. and Simplify3D for the best print;
- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Jurassic Park​ 3D Printing Figurine at Gambody YouTube channel.

You can get Model of Jurassic Park 25th Anniversary for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like other 3D Printing Figurines of Diorams.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

Generic

This model was tested in Cura 3.3.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for Cura and Simplify3D softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Speed 
Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 60 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings